This example for a Yún device shows how to use the Bridge library to send text messages from the Linux to the AVR. It demonstrate how you can create a queue of messages using REST style calls through the browser.
When running this example, make sure your computer is on the same network as the Yún device. Once you have uploaded the sketch on the board you can start to append messages in the Yún mailbox. The Mailbox will be checked every 10 seconds and the available messages displayed on the Serial Monitor. To use the REST APIs you need to insert the password or disable it from the Web panel. You can use a browser with the following URL structure: http://myArduinoYun.local/mailbox/hello
Yún board or shield
computer and Yún on the same wireless or wired network
There is no circuit for this example.
image developed using Fritzing. For more circuit examples, see the Fritzing project page
The example code shows how it's possible to make REST requests to the Yún deviceto send messages from the Linux side to the AVR. The messages are stored in a message queue, internal to the Linux side, and read by the AVR only when the readMessage() method is called.
You need to include only the Mailbox library because it automatically include the Bridge library:
1#include <Mailbox.h>
In
setup()
, start serial communication for debugging purposes, and turn the built-in LED on pin 13 high while Bridge begins. Bridge.begin()
is blocking, and should take about 2 seconds to complete. Once Bridge starts up, turn the LED off. Mailbox.begin()
starts the Mailbox on the OpenWrt-Yun and on the Arduino processor.1void setup() {2
3 pinMode(13, OUTPUT);4
5 digitalWrite(13, LOW);6
7 // Initialize Bridge and Mailbox8
9 Bridge.begin();10
11 Mailbox.begin();12
13 digitalWrite(13, HIGH);14
15 // Initialize Serial16
17 Serial.begin(9600);18
19 // Wait until a Serial Monitor is connected.20
21 while (!Serial);22
23 Serial.println("Mailbox Read Message\n");24
25 Serial.println("The Mailbox is checked every 10 seconds. The incoming messages will be shown below.\n");26}
In
loop()
, you'll create a String where to save the incoming message and call the Mailbox.messageAvailable()
function to read if there is an available message in the Mailbox.1void loop() {2
3 String message;4
5 // if there is a message in the Mailbox6
7 if (Mailbox.messageAvailable())8
9 {
If there is at least one message in the Mailbox, start to read all the messages in the queue and print it on the Serial Monitor.
1// read all the messages present in the queue2
3 while (Mailbox.messageAvailable())4
5 {6
7 Mailbox.readMessage(message);8
9 Serial.println(message);10
11 }
The Mailbox in the sketch is checked every 10 seconds using a
delay()
. This is also done to demonstrate the advantage to store data on the Linux processor instead of cluttering the RAM of the Arduino processor.1Serial.println("Waiting 10 seconds before checking the Mailbox again");2
3 }4
5 // wait 10 seconds6
7 delay(10000);8}
The full code is below:
1/*2
3 Read Messages from the Mailbox4
5 This example for the YunShield/Yún shows how to6
7 read the messages queue, called Mailbox, using the8
9 Bridge library.10
11 The messages can be sent to the queue through REST calls.12
13 Append the message in the URL after the keyword "/mailbox".14
15 Example16
17 "/mailbox/hello"18
19 created 3 Feb 201420
21 by Federico Vanzati & Federico Fissore22
23 This example code is in the public domain.24
25 http://www.arduino.cc/en/Tutorial/MailboxReadMessage26
27 */28
29#include <Mailbox.h>30
31void setup() {32
33 pinMode(13, OUTPUT);34
35 digitalWrite(13, LOW);36
37 // Initialize Bridge and Mailbox38
39 Bridge.begin();40
41 Mailbox.begin();42
43 digitalWrite(13, HIGH);44
45 // Initialize Serial46
47 SerialUSB.begin(9600);48
49 // Wait until a Serial Monitor is connected.50
51 while (!SerialUSB);52
53 SerialUSB.println("Mailbox Read Message\n");54
55 SerialUSB.println("The Mailbox is checked every 10 seconds. The incoming messages will be shown below.\n");56}57
58void loop() {59
60 String message;61
62 // if there is a message in the Mailbox63
64 if (Mailbox.messageAvailable()) {65
66 // read all the messages present in the queue67
68 while (Mailbox.messageAvailable()) {69
70 Mailbox.readMessage(message);71
72 SerialUSB.println(message);73
74 }75
76 SerialUSB.println("Waiting 10 seconds before checking the Mailbox again");77
78 }79
80 // wait 10 seconds81
82 delay(10000);83}
Last revision 2016/05/25 by SM